Oil & Gas

What Drill Rig Companies Need To Tell You Before You Drill a Well?

oil rigAccording to the working minds behind drill rig companies, the location and structure of your water well are critical to its safety. It should be placed in such a way that rainwater drains away from it.

Rainwater, on the land surface, runs the risk of gathering harmful bacteria and collecting an array of pollutants that may contaminate the water. If this water seeps anywhere near your well, it may jeopardize the quality of its water, and may thus pose health risks.

The construction of good water well is usually determined by local groundwater and geologic characteristics. Your local health department, the state’s licensing body for water-well contractors, or a specialist in the local water system can provide relevant information and guidance on acceptable construction norms in a particular area.

Make certain that any pump-well installers or drillers you hire for the job are insured and bonded. As your local government may require, verify that your groundwater contractor is duly certified for the role and has a proper license. 

Siting 

One should not look at groundwater exploration as a trial-and-error, hit-or-miss endeavor. Soil and rock beneath the ground act as a percolating medium for rainwater. Eventually, they get collected in saturation bed zones known as “aquifer beds”. 

A water well is a hole bored into the ground that makes it possible to reach an aquifer bed via which a small amount of groundwater can be pumped to the surface for consumption.

Drilling

Drilling a water well involves much more than just digging a hole in the ground. A fully accomplished water well will comprise a borehole drilled into the ground to reach the aquifer bed. 

Its diameter has to be large enough to accommodate the casing that will house the pump. The size of the pump required to satisfy your intended demand must be determined initially before digging starts

If you like your pumping power to go beyond 100 GPM, it is necessary to have a casing that measures 8 inches and goes with a 10-inch borehole, minimum. Your water well contractor will carry on making decisions about this, but you must make him aware of what your needs are. 

Developing

When you develop a water well, it will entail clearing it of the fine particles left behind by the drilling process itself. These fine particles will be flushed out of the gravel and aquifer between a good screen and the first few feet of the aquifer.

Bailing, surge pumping, or any other operation that propels water at high velocity via the development zone can be taken advantage of to accomplish development. 

Reputable drill rig companies are accountable for developing wells. Water wells that have been created properly will produce more water as opposed to water wells that are poorly constructed. 

Pump Testing

After constructing the water well, we have this looming question that begs us to ask. “How much water can we sustainably draw from it?” 

construction rig

The sustained rate of the pump is predicated upon the ability of the aquifer to send water towards this well under gravitational pull while the water well is being pumped. 

To determine a water well’s pumping capacity (sustained), a pump test should be done. Normally, your enlisted contractor for the job is the one to carry out the pump test. This part is usually included in the job contract.

It should be made clear also to your driller that you desire a pump test to be carried out before the start of the drilling because there are instances where they will not deliberately perform this part. 

Make sure you only enlist a driller or contractor who is capable of completing all aspects of the drilling tasks, and a pump test should be a part of that, too. 

 

Where to Build Your Water Well According to Drill Rig Companies?

drilling towerHomeowners, whether building a new home or making home upgrades, often have difficulty discerning where to place new water well. It becomes even more challenging when there are structures nearby their property like roads, community tanks, or a cell site area. Such structures and anything similar work to their disadvantage because they usually are a limiting factor to where you can construct a water well. Needless to say, locating the ideal site for new water well is not a straightforward thing. 

All three levels of government— the federal, state, and municipal— all have their own rules and laws regarding the water system and resources. If you are fully aware of the required setbacks together with the rolled out restrictions by the authorities and governing bodies regarding this, it could help assist homeowners and work to their benefit, help them in identifying a convenient site where they can have their new water well. 

Geological Research

It is quite easy for homeowners to learn something about their property. They must be familiar with the geology of the surrounding environment, and the construction details of the water wells in their region, because these matters are well documented and kept for public record-keeping purposes. 

Restriction on the construction of water wells began in 1984 by virtue of a state legislature. For drill rig companies to qualify as licensed contractors, they are required to submit a report that details construction specifications for every single water well drilling project at the end of each project.

Information submitted will be kept in an online database that the public can access. Details of the water well construction project, such as when it was built, the depth of the water well itself, and other relevant information can be accessed on such dedicated websites. 

If your old water well has failed and is not working anymore, make sure you document the construction details of your new water well if you are going to construct another one. 

drinking water

When selling a residential property with an onsite water system, it is crucial that you declare any kind of water system malfunctions there are or if there are any observable abnormalities with it. Alongside this, you also need to include the last time that a professional water quality test was carried out on your water well system. You can volunteer such information to your potential buyer.

Be Fully Cognizant of What Could Be Underground

Safety should always be contacted before beginning a good drilling project to avoid surrounding gas and electricity wires. 

When planning to construct a water well anywhere on your property, be sure to get in touch with any of the reputable drill rig companies in your area. Water wells need to be at a distance of 15 feet away from a gas line or an overhead power line. If the electrical network line is beyond 50 kV, be sure to construct your water well at least 25 feet away from it.

The natural geology of the area surrounding your property is another important factor to take into account. The vast majority of new wells installed today are bedrock wells. Although, we don’t rule out the possibility that some others are shallow wells instead. This is a possibility depending on the home. 

Bedrock wells are bored into the soil or, and as the name implies, bedrock formation that will provide enough water to work properly without interfering with neighboring wells. 

A reputable drilling contractor can advise you on the geology of and around your land. With that, they can advise you of the best type of well to have. 

Understanding the Purpose of Fire Cabinets

flammable fluidsFlammable liquids are incredibly beneficial in the modern society of ours, however their risky chemical as well as physical properties also present a selection of chances upon folks, property, and the atmosphere of the organization of yours. Flammable liquids are liquids which give off flammable vapors at temperature ranges below 60 °C. In case these flammable vapors enter touch with an ignition source, they are going to ignite and result in a serious fire. Additionally, large numbers of flammable vapors at the office can result in individuals to asphyxiate as well as pass out.

To mitigate the risks related to flammable liquids, they should be saved in a compliant and safe manner. This may be accomplished by having just about all flammable fluids in a compliant flammable storage box.

Purpose of Fire Cabinets

Protect contents within the medicine cabinet against damage

When flammable liquids are utilized in the workplace, it is essential to make sure that their packaging does not get damaged as well as the contents within the packages are not polluted. If packages of flammable fluids are harmed, it can result in the flammable fluids to problem out into the place of work. When flammable liquids are uncontained, they disperse flammable vapors a bit more readily. In case these flammable vapors enter touch with an ignition source, they are going to ignite and result in a serious fire which would damage property and people. A flammable liquids storage box that has been produced in total conformance to AS1940 will have a two skinned sheet steel building. This heavy-duty construction is going to protect the contents within the medicine cabinet from becoming harmed by outside moving objects.

Provide segregation between incompatible chemicals

Incompatible substances are things which are prone to increase risk to individuals, property and also the planet when mixed. If incompatible things mix, it might end up in a brutal chemical reaction. Violent chemical reactions can create explosions as well as the fast evolution of high heat and pungent deadly gases.

To stay away from the danger of brutal chemical reactions, incompatible things must be properly segregated. This may be accomplished by sorting incompatible substances by specific distances or even storing incompatible chemical substances in different protection cabinets.

Fire cabinets are particularly helpful for segregating flammable fluids from various other classes of dangerous items in confined spaces. Segregating flammable liquids from various other classes of dangerous products could be impractical in confined areas because the necessary segregating distance for flammable fluids from various other incompatible materials is around 3 to 5m.

Fire protection

If a fire incident took place in the workplace of yours and it came into touch with flammable fluids, the flammable fluids would immediately ignite as well as intensify the speed of fire spread. This incident type would decrease the possibility of employees escaping the fire.

To stop flammable liquids from immediately igniting in the occasion of a workplace fire, flammable liquids need to be kept in flammable storage space medicine cabinets which comply with AS1940. AS1940 outlines the exact demands for the layout and building of flammable storage medicine cabinets.

What is the Importance of Having Clean Self Bunded Diesel Fuel Tank?

Failed self bunded diesel fuel tank can be very costly over the long term because it will eventually cause you to replace your fuel pump. If your car right now gets you 20 miles to the gallon, doing the math here this means that there’d be around 5,000 that will go through your tank and that is in about 100,000 miles.  

It is wrong to think that this is okay because, during that time, foreign particles are likely to find their way into your tanks such as debris, rust, and sediment. Removing them is critical, though. One available option for this kind of scenario is to have your tank steam-cleaned.

diesel fuel tank


Reputable radiator shops can carry out that kind of service if they have one on offer. What they will do first is recondition your bunded diesel fuel tank and see to it that there are no leaks. One that you will find hard to spot on your own. Ultimately, the end goal you should have in cleaning your fuel tank is the restoration of the environment inside your fuel tank, back to the same state and condition it was in before putting fuel in before driving off the assembly line.  

If you are among the thousands of people who are under the impression that your new strainer or sock on your fuel pump is enough to catch out all the bad stuff, then all of you are dead wrong on this. It is typical for a strainer or sock to be designed for catching contaminates, but they are highly effective only in particles that are about 50-100 microns in diameter. For comparison purposes just so you have a how tiny they are, let us compare them to the human hair which is about 40 microns. Due to the small surface area that they usually come in, the sock consequently comes only with a limited capacity.  

Make it a habit to have a new filter installed. It may sound like a pretty simple thing to do, but most often than not this is forgotten by many. As time runs on your filter, it gets older and this could hinder flow, rendering your pump to work double time. This makes your pump forcibly run even on a higher temperature. Sooner or later, this would cause it to fail.  

The best practice that you can observe here is to filter your filter first before you even try to put them into your self bunded diesel fuel tank.

If there is a full meltdown for your fuel pump, there is a good possibility that pieces and fragments of your old pump remain in the removed fuel. So, therefore, it makes sense that you filter your fuel first before you put them back in your tank. There are a handful of fuel caddies that come with built-in filters. You may want to check them out for this.  

So, what other things you need to look out for that can kill your new fuel tank pump? Bad grounds and connections may also bring about the same thing to your pump. For this, you will need to check out your connector and try to look for any visible signs of thermal damage. They indicate that there has been a voltage drop before. It is also a positive sign that there has been a circuit with high resistance. 

Do not allow yourself to get into the habit of making assumptions that it is always your old pump that brought about the thermal damage that you are seeing. Bad circuits and grounds are about to stay and remain with the vehicle, inducing a measurable amount of damage to your new pump.  

It is also of prime importance that you assess the EVAP system. Most vehicles would require 1 drive cycle for this and only after that will it allow you to set up an EVAP code. A leak brought about by a disturbing line may keep it from setting a code while the initial test drive is ongoing. It may come after some time that your vehicle remained sitting for a while or at that point when its temperature has subsided.  

Top Performing Drill Rig Companies Today

Which among the drill rig companies we have today are considered the major players in the industry? How do they impact global businesses with their actions? 

Drilling oil wells that will substantially help the world produce its required energy is a collaborative effort of a unified team. Currently, we have 3 kinds of drill rig companies that work on tapping these sources of energy from mineral oil, namely drilling contractors, oilfield services and manufacturing companies, and  E&P companies. 

drill rig companies

What do the E&P companies do?

The heart of their work lies in the research work they do, in the hope of finding resources for subsurface hydrocarbons. It allows them to oversee the process of drilling work. In addition, they can also take charge of managing hydrocarbon transportation,  the processing of gas and sometimes even handling petroleum refining, too. 

They can also employ drilling contractors, providing crews and drilling rigs along the way.  Some of them will also contract some oilfield service teams to help them obtain additional equipment and materials for the website. All these companies together comprise the gas segment and upstream oil. 

Leading Offshore Drilling Companies

Schlumberger

Right now, Schlumberger is one of the leading names in the top global offshore drilling organizations. With respect to generated annual revenue, they are regarded as the biggest contractor for the offshore drilling sphere. And this is not only in the US territory but even from across the world it carries a history of technology and science innovation. They are often backed by acquisitions and strategic mergers. 

From application-specific down to conventional systems for jack-ups, rigs, geothermal wells, their offered drilling services are designed in such a way they will help in further enhancing safety levels and trim downtime for installation.  

Halliburton

Throughout a reservoir lifecycle, Halliburton will serve it the gas sector and upstream oil kit it requires, from managing geological data to locating reserves and drill assessment, well construction, production optimization and completion throughout the entire lifetime of the field. 

The offshore drilling services they have on offer would include directional and horizontal drilling, logging while drilling, measurement while drilling, rig site systems information, multilateral systems, and underbalanced applications. 

Baker Hughes

The field of specializations for Baker Hughes can be found in drilling, production, and, oil and gas completion services.  The offshore drilling services they offer include measurement-while-drilling, directional drilling services, logging-while-drilling, coiled tubing and re-entry,  and remote drilling. Norwegian sea’s Skuld offshore field is one of the biggest offshore oil fields where they have their offered drilling services for deep-water. 

KCA Deutag

KCA Deutag is one of the UK’s leading offshore drilling organizations. Right now it is included in the roster of leading global providers of engineering and drilling expertise. They currently have operations,  both offshore and onshore. 

The organization, in the past few years, was able to garner some new contracts to work on and get themselves preoccupied with. With an industry experience spanning 125 years, they are one of those leading drill rig companies that are anticipated by insiders to dominate on a global scale the offshore drilling sphere. 

This drilling organization is comprised of 4 business segments: oilfield equipment,  manufacturing, design and engineering, and offshore drilling. There are currently 90 drilling rigs under their management and care. These drilling rigs are dispersed in more than 20 countries around the globe. 

Silvan Tanks and the Importance of Proper Maintenance

Much like any other fuel containment systems, silvan tanks need proper care and maintenance, too.

The composition of modern fuels we have today necessitates that we store them inside fuel containment systems that are properly cleaned and well maintained. Fuel integrity is an important factor to have if you want to maintain your fuel containment system’s reliability. 

However, the downside here is that when you have your fuel stored for an extended period of time, it runs the risk of developing sediments along the way. Random fuel particles may also form and get deposited at the bottom part of the tank, they are more popularly known as sludge. Water and other contaminants may also accumulate, and if that happens, it will require you to have fuel polishing. If you leave such contaminants untreated for far too long a time, they will eventually cause mechanical and engine failures.  

Below are some of the points that will help us underscore why proper maintenance practices for your silvan tanks is extremely important

mechanical engineering

Use Only Clean Fuel to New Engines 

The technology that is working behind a fuel injection system that you see in vehicle engines undergo constant improvements. By this measure, these vehicles become fuel-efficient. The use of new injectors makes way for more efficient and faster combustion, which also leads to the creation of fine mists. 

New fuel injections clog more easily, they are highly precise and need cleaner fuels. It is very important to keep fuel injectors clean because that will significantly help in keeping the engine free from damage. Clean and well-maintained fuel tanks translate to cleaner fuel. And cleaner fuel means to say that you have much cleaner fuel injectors.  

BioFuels Need Monitoring

A new breed of biofuels is all coming into play. Biodiesels are also slowly gaining some foothold in the marketplace. Compared to traditional liquid fuels that we are accustomed to having, these biofuels burn cleaner and a lot more efficient.  

But there is one drawback here you need to be made aware of as early as now. When it comes to this type of fuel, water is a bigger concern that you will need to deal with. It can easily get dissolved in ethanol than when it is in petrol. Therefore, it is safe to say that ethanol-blended fuels are likely to hold greater amounts of water than suspension type. 

Biofuels also tend to absorb more water from the air. The best way to safeguard your liquid fuel such kinds of concerns is to ensure that you are employing proper maintenance practices to your fuel containment systems. This way your stored high-value liquid will remain clean and stable.  

We must have in place proper risk management measures. Everyone assigned or delegated to work around a piece of equipment or within an arm’s reach to a fuel containment system should be properly trained in the proper identification and elimination of risks. In addition to this, they ought to know and must be well versed in conducting routine inspections, dispensing fuel, and how to properly operate pump shutoff mechanisms.